Modifications for the Kenwood TS-450

Picture(s) of Kenwood - TS-450

19-07-1998 KAM-PLUS Problems!! with TS-450 & 850 English language (2 Kbytes)
19-07-1998 General coverage transmisson modification for the TS-450 and TS-690 English language (1 Kbytes)
19-07-1998 TS-450S Intermittent receive fixed English language (1 Kbytes)
19-07-1998 TS-450,TS-850 feedback,ACC-2 Conn English language (1 Kbytes)
19-07-1998 TS-450 hidden functions English language (2 Kbytes)
19-07-1998 TS-450S and KAM Plus info English language (0 Kbytes)
20-02-1999 Micro-input RFI modification TS450-TS690 Kenwood English language (2 Kbytes)
21-04-2000 TS-450/690 Calibration cable change English language (7 Kbytes)
22-04-2000 TS-450/690 Distorted TX w/TNC English language (50 Kbytes)
22-04-2000 TS-450S TX frequency response English language
23-04-2000 TS-450/690 Low mic gain w/DSP-100 English language (21 Kbytes)
23-04-2000 TS-450S Parts change English language (23 Kbytes)
23-04-2000 TS-450S/690S Noisy encoder English language (1 Kbytes)
 View all modification in one click. This can be a very big file.!! (113 Kbytes)

22-04-2000
TS-450S TX frequency response
Author: Kenwood Communication, inc.


Service Bulletin no. 1004 (21 December 1992)

We have received several reports concerning the transmit audio quality of this unit. Several reporters noted that the signal sounded "hard" or had a reduced bandwidth, while others noted a difference in the noise quality when switching between USB and LSB. We noticed a significant difference between the output power in LSB and USB on some of these sets.

Cause:
Improper adjustment of the 8.83 MHz tuning coils (L73, L76) on the RF unit (X44-3130-00) can cause these symptoms. The coils have two tuning points. One is reached when the tuning slug project above the surface of the coilk form. When tuned in this manner the bandwidth becomes narrow then normal and causes the symptoms noted above.

Alignment procedure:

  1. Adjustment should be performed with the YK-88S1 (2.4 KHz) filter in line. If this filter is not preset you should select the THRU position for the 8.83 MHz IF.

  2. Adjust L73 and L76 according to the instructions provided in the service manual (Item 6 of the Receiver adjustment). Ensure that the slug are preset well down in the coil form, then adjust for peak. You should reach this point before the top of the slug exist the coil form.

  3. Next, readjust L74 and L75 (Item 8 of the Receiver adjustment).
    1. Select the 6 KHz filter for both the 8.83 MHz IF and the 455 KHz IF.
    2. Select a dial frequency of 14.100.4 MHz.
    3. Select the USB mode.
    4. Adjust L74 and L75 for maximum.
    5. Select the LSB mode.
    6. Readjust L74 and L75 for maximum.
    7. Repeat steps 3c - 3f several times until you obtain a difference of 2 dB or less in the AF output when switching between USB and LSB.


  4. Check Item 14, CAR point adjustment (Transmitter section) Menu items 11 and 12, and confirm that the transmitter power is equal for USB and LSB.

Time required for this modification is 30 minutes or less.

This modification is read 446 times.

top of page

Have you any tips, trick or modifications you can't find here, please E-mail them to me, or use the mail form.
Can't you find a mods, please don't e-mail to me. All mods i have is listed on this site.!
Back to start page

Valid HTML 4.0!